본문 바로가기 주메뉴 바로가기

MAKER (제조사별 제품보기)

MAKER

List
Prev Next

SG 시리즈 (DC전원공급기)

파워 4 kW - 150 kW
전압 10 V - 1000 V
전류 5 A - 6000 A
사이즈 3U or 6U, 19인치
인터페이스 RS-232(옵션), GPIB(옵션), LAN(옵션)
데이터시트

소렌센 SG 시리즈
 Sorensen SG 시리즈 (이하 SG 시리즈)는 차세대 고전력 프로그래밍 가능 DC 전원 공급 장치를 나타냅니다. SG 시리즈는 업계에서 탁월한 부하 과도 응답, 저잡음 및 최고 전력 밀도를 위해 설계되었습니다. SG 시리즈는 3U 패키지로 20VDC까지 출력을 15kW까지 이용할 수있어 업계 최고의 전력 밀도를 제공합니다. 세련된 전면 공기 흡입구로 전력 밀도가 향상되어 장치 간 간격이 없어도 소모품을 쌓을 수 있습니다.

 SG 시리즈의 핵심은 5kW 전력 모듈입니다. 출력 전압에 따라 단일 섀시에 1-6 개의 모듈을 구성하여 5kW에서 30kW의 전력을 공급할 수 있습니다. 이 섀시의 조합을 쉽게 병렬로 연결하여 최대 150kW의 전력 수준을 달성 할 수 있습니다. 병렬 장치는 전체 시스템 전류를 제공하는 단일 공급 장치처럼 작동합니다. 두 가지 제어 버전으로 제공되는 SGA에는 기본 아날로그 제어 기능이 있으며 SGI는 지능형 제어 기능을 제공합니다.

​

SGI : 고급 지능형 제어
 (Sorensen 범용 인텔리전스) SGI는 온보드 지능형 컨트롤과 모든 SG 제품군 공급 장치에 공통적 인 뛰어난 전력 전자 장치를 결합합니다. 이 컨트롤은 정교한 시퀀싱, 정 전력 모드 및 계측기 설정 저장 / 호출을 가능하게합니다. 시퀀스 반복은 SGI를 반복 테스트에 이상적으로 만듭니다. 8 가지 언어로 된 진공 형광 그래픽 디스플레이, 상황에 맞는 "소프트"키 및 전면 패널 키보드는 SGI의 프로그래밍을 단순화합니다.

​

SGA : 탁월한 가치-아날로그 제어
 (Sorensen 범용 아날로그) 업계 최고의 성능을 자랑하는 SGA는 간단한 전면 패널 아날로그 컨트롤 또는 외부 컨트롤이 필요한 고객에게 제공됩니다. SGI와 동일한 고성능 전력 전자 장치를 갖춘 SGA는 전압 및 전류 설정을위한 10 턴 전위차계, 3 ½ 자리 LED 판독 값 및 전면 패널 과전압 보호 (OVP) 미리보기 / 조정 및 재설정과 같은 필수 기능을 제공합니다.

​



SGI / SGA Comparison Chart

FeatureSGASGI
Modular Design••
Fast Load Transient••
Parallelable••
Analog & Digital SummingOptional•
Direct Front Panel V/1 Control••
3½ Digit LED Readout•
Graphics Display•
Sequencing•
Save / Recall Setups•
System Power Readouts•
Constant Power Mode•
IEEE-488.2/RS-232COptionalRS-232C Std
IEEE-488.2 Optional
LXI Class C Ethernet/ RS-232OptionalRS-232C Std, Ethernet Optional
Front Panel Dust FilterOptional (3U unit only)Optional (3U unit only)
Applications
Burn-InCompliance Testing
Materials ResearchProcess Control
Product ValidationAutomotive Electronics
Rackmount ATE SystemsBattery Charging
See the SFA product page for very high current slew rate and low stored energy applications.

​

 


  • Specifications +


    Sorensen SG Series Specifications
    Common
    Remote Sense Terminals are provided to sense output voltage at point of load. Maximum line drop 5% of rated voltage per line f
    Parallel Operation Up to 5 units may be paralleled for additional current within the power supply single-unit specifications, with exception of the DC output current set accuracy. Additional paralleled SG units will add 0.3% inaccuracy per unit. To parallel more than 5 units, contact factory.
    Series Operation Up to 2 units (see Output Float Voltage)
    Input
    Nominal Voltage
    3 phase, 3 wire + ground    		 208/230 VAC (operating range 187 - 253 VAC)
    380/400 VAC (operating range 342 - 440 VAC)
    440/480 VAC (operating range 396 - 528 VAC)
    Frequency 47 – 63Hz , 400Hz ( 400Hz @ 208VAC, for 6U units is optional modification and does not carry CE, UL or CSA markings )
    Power Factor >0.9 typical for 10V - 30V, 50V, 1000V and other models with optional “PF” modification.
    >0.75 typical for 208/220 VAC input
    (40V, 60V - 800V models, 0.9 available with modification “PF”)
    >0.72 typical for 380/480 VAC input
    (40V, 60V - 800V models, 0.9 available with modification “PF”)
    >0.69 typical for 440/480 VAC input
    (40V, 60V - 800V models, 0.9 available with modification “PF”)
    Protection ½ cycle ride-though , typical, on all three phases, 3 cycle ride through on single phase; missing phase shutdown ( 800V model 6.4 msec on all 3 phases )
    Programming & Read-back Specifications ( with sense wires used )
      Programming Read-Back / Monitoring  
    Accuracy Resolution Accuracy Resolution
    Front panel Display

    SGA: +/- (0.5%fs + 1 digit) SGI (40-1000V) +/- 0.1% of voltage at full scale SGI (40-1000V) +/- 0.4% of current at full scale

    		 SGA: 3.5 digits SGI: 4.0 digits

    SGA: +/- (0.5%fs + 1 digit) SGI, Voltage: +/- 0.1% of full scale SGI, Current: +/- 0.4% of full scale

    		 SGA: 3.5 digits SGI: 4.0 digits Knob control & Display read-back
    SGI (10-30V) 0.1% of set point +0.1% of voltage rating SGI (10-30V) 0.1% of set point +0.4% of current rating SGI (10-30V) 0.1% of actual +0.15% voltage rating
    Remote Analog Interface Voltage +/-0.25% of full scale Current (40-1000V) 0.8% of full scale , (10-30V) 1.0% of full scale N/A

    (40-1000V) +/-1.0% of full scale

    		 N/A 25-pin D-sub connector (0~5 V or 0~10 V)
    (10-30V) +/-0.5% of full scale
    Remote Digital Interface Voltage: +/- 0.1% of full scale, Current: +/- 0.4% of full scale +/-0.002% of full scale Voltage: +/- 0.1% of full scale
    Current: +/- 0.4% of full scale    		 +/-0.002% of full scale RS-232C (Standard on SGI), Optional IEEE-488.2 and Optional LXI Compliant 10/100 base-T Ethernet (see Options)
    OVP +/- 1% of full scale +/-0.002% of full scale     Programming range: 5-110% Configured from front panel, remote analog or via optional digital inputs
    User I/O Disconnect & Polarity-reversal relay control ( Only available with Ethernet Option ) Digital 10-pin Molex type connector Chart Below
    Software IVI & CVI drivers available under DOWNLOADS at: www.ProgrammablePower.com
    Physical
      3U Models (10V-30V) 3U Models (40V-1000V) 6U Models (60V-600V)
    Width 19.00 in (48.3 cm) 19.00 in (48.3 cm) 19.00 in (48.3 cm)
    Depth 28.09 in (71.35 cm) 26.4 in (67.1 cm) 27.06 in (68.8 cm)
    Height 5.25 in (13.3 cm) 5.25 in (13.3 cm) 10.5 in (26.7 cm)
    Weight

    (4kW, 10V 15V) ≈<65 lbs (29 kg)
    (5kW, 20V 30V) ≈<65 lbs (29 kg)
    (8kW, 10V 15V) ≈<85 lbs (39 kg)
    (10kW, 20V 30V) ≈<85 lbs (39 kg)
    (12kW, 10V 15V) ≈<110 lbs (50 kg)
    (15kW, 20V 30V) ≈<110 lbs (50 kg)

    (5kW) ≈ ≤60 lbs (27 kg)
    (10kW) ≈ ≤75 lbs (34 kg)
    (15kW) ≈ ≤90 lbs (41 kg)

    (20kW) ≈ ≤140 lbs (64 kg)
    (25kW) ≈ ≤155 lbs (71 kg)
    (30kW) ≈ ≤170 lbs (78 kg)
    Shipping Weight Contact factory for more product & shipping weights
    Output
    Ripple & Noise (Voltage Mode, Typical) See Output: Voltage & Current Ranges Chart above. Ripple and noise specified at full load, nominal AC input. Noise measured with 6ft. cable, 1μf at load
    Output Rise Time (40-800V) ≈< 100 ms 5-95% of full scale typical - resistive load (Contact factory for model specific slew rates)
    Output Rise Time
    (10-30V)    		 Rise Time, ms, MAX Condition
    10 Measured from 10% to 90% of the output voltage change - resistive load, typical
    Output Voltage Fall Time
    (10-30V)    		 Fall Time, MS MAX Condition
    No Load 1
    50    		 100% CC Load 10 100% CR Load 10 Measured from 90% to 10% of the output voltage change. - resistive load, typical
    Output Current Rise Time
    (10-30V)    		 Rise Time, ms, MAX Condition
    20 Measured from 10% to 90% of the output current change - resistive load, typical
    Output Current Fall Time
    (10-30V)    		 Rise Time, ms, MAX Condition
    10 Measured from 90% to 10% of the output current change - resistive load, typical
    Line Regulation (with sense wires used) (±10% of nominal AC input, constant load)
    Voltage Mode: +/- 0.01% of full scale (40-800V)
    Current Mode: +/- 0.05% of full scale (40-800V)
    Voltage Mode and Current Mode: +/- 0.05% of full scale (10-30V)
    Load Regulation (with sense wires used) (no load to full load, nominal AC input)
    Voltage Mode: +/- 0.02% of full scale (40-800V)
    Current Mode: +/- 0.1% of full scale
    Voltage Mode: +/- 0.05% of full scale (10-30V)
    Load Transient Response Recovers within 1ms to +/-0.75% of full-scale of steadystate output for a 50% to 100% or 100% to 50% load change
    Efficiency 87% typical at nominal line and max load
    Stability ±0.05% of set point after 30 minute warm-up and over 8 hours at fixed line, load and temperature, typical
    Temperature Coefficient 0.02%/ C of maximum output voltage rating for voltage set point, typical
    0.03%/ C of maximum output current rating for current set point, typical
    Output Float Voltage Negative terminal within +/- 300 V of chassis potential.
    (We recommend the use of optional isolated analog Interface (IAI).) Supplies in "series" should be the same output voltage/current, in not system current is limited to lower of the two supplies.
    Environmental
    Operating Temperature 0 to 50º C
    Storage Temperature -25º C to 65º C
    Humidity Range Relative humidity up to 95% non-condensing, 0º C – 50º C
    Altitude Operating full power available up to 5,000 ft. (~1,500 m), derate 10% of full power for every 1,000 feet higher; non-operating to 40,000 ft. (~12,000 m)
    Cooling Front and side air inlet, rear exhaust. Temperature controlled, variable speed fans. Units may be stacked without spacing.
    Regulatory Certified to UL/CSA 61010 and IEC/EN 61010-1 by a NRTL, CE Compliant, Semi-F47 Compliant.
    LVD Categories: Installation Category II: Pollution Degree 2; Class II Equipment: for Indoor Use Only, back panel not user accessible
    (see user manual for installation instructions)
    EMC Directive, EN 61326:1998
    Front Panel Dust Filter 30 PPI (Pores Per Inch) - must ensure adequate airflow and / or derate max. temperature.
    3U unit only.
    Output: Voltage and Current Ranges
      3U
    Power 4/5 kW 8/10 kW 12/15 kW
    Voltage Current
    10 400 800 1200
    15 267 534 801
    20 250 500 750
    30 167 334 501
    40 125 250 375
    50 100 200 300
    60 83 167 250
    80 63 125 188
    100 50 100 150
    160 31 63 94
    200 25 50 75
    250 20 40 60
    300 17 33 50
    330 15 30 45
    400 12 25 38
    500 10 20 30
    600 8 17 25
    800 6.2 12.5 18.7
    1000 5 10 15
    Output: Voltage and Current Ranges
      6U
    Power 16/20 kW 20/25 kW 24/30 kW
    Voltage Current
    10 1600* 2000* 2400*
    15 1068* 1335* 1602*
    20 1000* 1250* 1500*
    30 668* 835* 1002*
    40 500* 625* 750*
    50 400* 500* 600*
    60 333 417 500
    80 250 313 375
    100 200 250 300
    160 125 156 188
    200 100 125 150
    250 80 100 120
    300 67 83 100
    330 61 76 91
    400 50 63 75
    500 40 50 60
    600 33 42 50
    800 25* 31.2* 37.5*
    1000 20* 25* 30*
    * By way of paralleling 5kW, 10kW & 15kW supplies
    Read-back Specifications
      Ripple & Noise
    Voltage rms (20Hz-300kHz) p-p (20Hz - 20MHz)
    10 20mV 50mV
    15 20mV 50mV
    20 20mV 60mV
    30 20mV 60mV
    40 20mV 75mV
    50 20mV 75mV
    60 20mV 75mV
    80 20mV 100mV
    100 20mV 100mV
    160 25mV 150mV
    200 25mV 175mV
    250 30mV 200mV
    300 30mV 200mV
    330 30mV 200mV
    400 30mV 300mV
    500 50mV 350mV
    600 60mV 350mV
    800 80mV 500mV
    1000 100 mV 650 mV
    * By way of paralleling 5kW, 10kW & 15kW supplies
    Analog User I/O Pinouts
    1 Isolated Remote ON/OFF 14 Isolated TTL/CMOS ON/OFF Control
    2 Isolated Circuit Return 15 Remote Voltage Programming
    3 Remote Overvoltage Set 16 Remote Current Programming
    4 Voltage Return for Pins 9, 15, or 21 17 Fault State
    5 Remote ON/OFF 18 Shutdown Fault
    6 Circuit Common 19 Output Voltage Monitor
    7 Output Current Monitor 20 Voltage Return for Pins 9, 15, or 21
    8 Local Voltage Control Monitor 21 Voltage Control Resistance
    9 Remote Voltage Programming 22 Current Control Resistance
    10 Remote Current Programming 23 Current Return for Pins 10, 16, or 22
    11 Local Current Control Monitor 24 Circuit Common
    12 Not Used 25 Current Return for Pins 10, 16, or 22
    13 Not Used  
    Digital User I/O Pinouts ( Ethernet Option Only )
    1 Fold Back Monitor
    2 Direct Shutdown
    3 Fault Indication
    4 Trigger Out
    5 Common
    6 Polarity output reversal signal
    7 Isolation relays relay open signal
    8 Sense relays open signal
    9 Common
    10 Trigger in

    • SG : Model Number Description

     

     

    Options and Accessories

    Control Options

    A Analog

    I Intelligent

    Input Voltage Options

    C Input Voltage 187 / 242VAC

    D Input Voltage 342 / 440VAC

    E Input Voltage 396 / 528VAC

    Remote Control Options

    0A No Options

    1A IEEE-488.2 + RS-232C (RS-232 comes standard on SGI

    1C Ethernet / RS-232

    1D Isolated Analog Control

    1E Shaft Locks (SGA series only)

    2A Combined Options 1A + !D

    2G Combined Options 1C + 1D

    2H Combined Options 1C+1E (SGA Only)

    2J Combined Options 1D+1E (SGA Only)

    3C Combined Options 1A+1D+1E (SGA Only)

    3G Combined Options 1C+1D+1E (SGA Only)

    Process options

    AA No Options

    AB AB: Certificate of Calibration to ANSI / NCSL Z540-1 (includes Test Data)

    Modifications

    AJ Front panel dust filter - factory installed - 3U unit only

    CV 400Hz AC input @ 208 VAC ( does not carry CE, CSA or UL marks ) ( 6U only ) STD on 3U

    PF Passive power factor correction to 0.9 (Only applicable to 40V, 60V to 800V. Included in 10V-30V and 50V.)

    Accessories

    890-453-03 Paralleling Cable (for up to 5 units, requires one cable per unit placed in parallel)

    K550212-01 3U Rack Slides (for 5kW, 10kW and 15kW models)

    K550213-01 6U Rack Slides (for 20kW, 25kW and 30kW models)

    K550532-01 Front panel dust filter - field installation kit - 3U unit only

    9550589-01 AC input cover - 3U unit only

    5551082-01 Optional AC input cover kit - 3U unit only

    Contact factory for other combinations